Commercial Reverse Osmosis Water Filter Dental Aquarium Laboratory CRO-RO SS

HIGH FLOW REVERSE OSMOSIS WATER PURIFIERS

SELECT SYSTEM FLOW RATE FROM DROP DOWN MENU 

THIS UNIT IS LEAK TESTED & PERFORMANCE RATED IN QLD AUSTRALIA

PRODUCT CODE: CRO-RO-LPD*
*LPD PER FLOW RATE SELECTED
 
STAINLESS STEEL / WHITE POWDER-COATED MILD STEEL FRAME

We have purposefully designed this system with minimal electronics and don’t use solenoids for longevity and less repairs and maintenance over the life of the unit. Replacement parts for this unit are easy to source, cost effective, not difficult to replace and give very few issues whereas in our experience these units built with PC boards and flashy electronics can become difficult to maintain in future. The picture in this listing is a stock item pictures and the unit you receive may look slightly different i.e. the membranes are normally mounted on the back and not top and some systems may have one pump instead of two pumps depending on the production flow rate required.

The reverse osmosis process produces the purest possible water and results in the total dissolved solids (TDS) count dropping by between 85% and 95% depending on environmental factors and system design. This purification process is commonly considered to be the most effective method of purification available to the public, and will consistently produce water with the lowest level of contaminant. Where water of a higher standard (99-100% contaminant reduction) is required, Mixed resin post filters may be fitted on request for an extra charge. 

 This system will produce between +/- 500 and +/- 3,750 litres per day depending on the system selected and the purity level required [note that local water pressure and quality of the feed water can cause this estimate to vary]. This unit is tested on a town water supply, if you plan to use this unit on any other kind of supply (bore, creek, tank, etc) we strongly recommend performing basic water tests (TDS, Salinity, Hardness / Calcium and Iron) to determine whether the water is within the systems operating parameters. If you are unsure as to whether this unit suits your needs, feel free to send us a message with any details you have on your water, a TDS reading is the most important for us. We sell a basic TDS reader here

Reverse Osmosis will reduce all of contaminant found in the feed water. Different types of contaminant have different reduction rates, see the below table for the effective reduction rates of common contaminants. Note that reduction rates may vary for alternative compounds of the chemicals listed below and different environmental factors.

All of the parts that come into contact with the water in our systems are manufactured from BPA free food grade plastics. All of the filters and parts that we source are of the highest quality and meet the required quality standards.

SYSTEM INCLUDES:

• 316 marine grade stainless steel stand/frame
• Three 20"x2.5" big blue pre-filter housings
• One 20x2.5 poly spun sediment filters (we may advise that you change this combination depending on your source water)
• Two 20x2.5 carbon block filter cartridges (we may advise that you change this combination depending on your source water)
• Reliable diaphragm booster pump/s (including Australian approved transformer/s)*
• An array of high quality NSF certified reverse osmosis membrane elements
• Appropriate ring spanner to loosen and tighten the pre-filter housings
• Image 2 shows the dimensions of the system however the stand supplied is the one in the 1st [main[ listing image.

*Systems may be supplied with one or two pumps and pump flow rates may vary but will achieve at least the advertised production flow rate given minimal inlet feed water pressure. These units have low pressure switches to protect the pump from running dry and you'll need at least 20psi inlet water pressure for the low pressure switch to engage the pump [if you don't the low pressure switch will need to be bridged for the pomp to work].

The system is supplied as a complete unit, all you will need to do is connect the 1/2"BSP feed water inlet, product water and waste water outlets and power to operate the unit and where feed water is particularly bad extra pre-filtration may be required, please inquire to see if this may apply to you.

If you need delivery to a regional area a delivery surcharge may apply depending on the cost of freight so if you're not sure please contact us and ask whether we can include free delivery to you area and if not what would your delivery cost surcharge be before buying this item.

We supply these units with a 4-way shut off valve, a non return valve, a low pressure switch and a high pressure switch so that the unit can be setup to run automatically if you install a float valve [not included] in the tank you'll be using this unit to fill you may need to purchase a small buffer tank if you set this up and the waste is not shutting off in your environment. These small buffer tanks range from $49.50 for a 2 litre to $149.50 for a 12 litre tank and aren't always needed so it's best to test whether the waste shuts of in your setup and if not then add the buffer tank.

This RO unit carries a full 24 month warranty on all parts supplied in the original order, this is subject to our standard terms and conditions listed in our operating manual

If you are not entirely satisfied with your purchase please contact us so that we can try to resolve your concerns

We pre-assemble these units however before dispatching them we flush the membranes, leak test the unit, test the 4-way shut off valve and the low and high pressure switches and record all performance results. Thereafter we pack and dispatch the unit and this process takes 2 working days excluding the delivery of the unit which depends on where you are located. Paying extra for express post on this item will upgrade you from standard post to TNT Road Express if they service your region but if you are very reginal we recommended not paying extra for express post as you most likely won't receive your order any sooner.

NB NOTE: Watermark certification is not a requirement with commercial systems unless you plan to use this unit in a domestic household connected to mains water supply then you may require housings with Watermark certification which we can supply for $ 100 extra and the onus is on you to let us know if you require Watermark certification at the time of ordering as changing this after the unit has been dispatched will cost up to 5x as much if we have to ship a unit to you, have it chipped back and change the housings to be Watermark certified ones.